Moroso Products Alphabetical Index
| Moroso Performance Products - Catalog |
| Air Cleaners & Accessories, Exhaust System, Valve Train Equipment, Valve Covers & Accessories |
RPM - RON'S PRECISION MACHINE, INC.
69 E. 580 N.
Santaquin, Utah 84655
https://www.rpmrons.com
1-801-754-5338 or Toll free 1-866-700-5877
| Contact us anytime OR use your e-mail program and type in ron@rpmrons.com to send an e-mail with what you need |
| Engine Rebuild Kit and Parts Online Catalog. |
|
Hours: 9:00 AM to 5:00 PM Monday - Friday mountain time (Utah) Call toll free to purchase parts at: 1-866-700-5877 U.S. only |
Moroso Products Alphabetical Index
| Scroll down to see what you need then cick on the page link to the right of the table if there is one. |
| . | Page(s) |
| RACE SUPPORT & CONTINGENCY | 1 |
| PRODUCT INDEX for this page only | 2-7 |
| NEW PRODUCTS FOR 2017 | 8-29 |
| OIL PANS & ACCESSORIES Small Block Chevrolet | 30-45 |
| OIL PANS & ACCESSORIES LS series |
|
| OIL PANS & ACCESSORIES LT series |
|
| OIL PANS & ACCESSORIES Big Block Chevy | 55-66 |
| OIL PANS & ACCESSORIES Chryler, Ford | 67-92 |
| OIL PANS & ACCESSORIES Oldsmoble | 93-101 |
| Oil Pan Accessories | 104-111 |
| OIL PUMPS | 112-133 |
| OILING SYSTEM | |
| VACUUM PUMPS & ACCESSORIES | |
| MOUNTING BRACKETS | |
| OIL PUMP & VACUUM PUMP DRIVE KIT & PULLEYS | |
| AIR/OIL SEPARATORS | |
| TANKS & COVERSALS | |
| TRANSMISSION PANS & ACCESSORIES | |
| CHEMICALS | |
| FASTENERS | |
| BRAKE & WHEEL EQUIPMENT | |
| TRICK SPRINGS | |
| TOOLS | |
| MOTOR & TRANSMISSION MOUNTS | |
| COOLING SYSTEM | |
| FUEL SYSTEM EQUIPMENT | |
| AIR CLEANERS & ACCESSORIES | |
| EXHAUST SYSTEM | |
| VALVE TRAIN EQUIPMENT | |
| VALVE COVERS & Accessories | |
| IGNITION WIRE |
310-332 |
| IGNITION SYSTEM |
333-347 |
| ELECTRICAL SYSTEM |
348-359 |
| REAR AXLE EQUIPMENT |
360-361 |
| SHEETMETAL & BODY |
362-363 |
| STEERING |
364 |
| TIRES |
365-366 |
| APPAREL |
367-368 |
|
New Products section Pages 8-29 A Air Cleaners and Accessories..................... 273-279 Air Cleaner Base Gasket................................... 276 Air Pan Kits, Carburetor............................. 233, 277 |
|
|
|
C (con’t) Coil Mount Bracket Kit........................... 288 |
|
|
|
G Gasket, Air Cleaner Base................. 276 Gaskets, Valve Cover..................... 24, 300 Grommets PCV /Baffles............. 307-308 H Header Flange Kit............................. 279 Header Wrap..................................... 279 Heat Barrier Blanket........................ 279 |
|
I Insulating Header Wrap.................. 279 L Low-Profile Air Cleaners................. 273 LS GM Coil Mounts........................ 288 |
|
|
|
R Rear End & Water Fill Cap Kits....... 309, 361 Remote Coil Mounting Bracket........... 288 Removable Coil Mounting Bracket..... 288 |
|
S Sleeves, Boot 329 Spiral Flow Racing Muffler................... 278 Stud Girdles and Accessories, Valvetrain.............................................. 280 |
|
|
|
V Valve Cover Accessories.................... 300-309 Valve Cover Acorn Nuts............................ 301 Valve Cover Baffles, Grommets........ 307-308 Valve Cover Breathers....................... 305-307 Valve Cover Gaskets............................... 24, 300 Valve Cover Hold Down Tabs............. 300-302 |
|
V (con’t) Valve Cover Oil Fill Kit........................... 309 Valve Cover Wing Nuts........................... 301 Valve Covers............................... 24, 281-309 Valve Train Equipment............................. 280 Valve Train Oil Deflector...................... 148, 280 W Wet Sump vs. Dry Sump Oiling Information .....................................31 Wing Nuts, Air Cleaner............................. 301 |
|
LOW-PROFILE RACING AIR CLEANERS For years, Moroso Air Cleaners and accessories have set the standard by which all others are judged. Whether in triple process chrome steel, powdercoat or our unique fiber design, Moroso Air Cleaners provide the racer or street performance enthusiast with improved air flow, a lower stacking height, and unequalled fit and finish. Moroso Air Cleaners and accessories are simply the best money can buy! |
|
BETTER AIRFLOW! • Moroso’s unique radiused air inlet design equalizes air pressure past the boosters for uniform air flow • Radiused air inlet is stamped into air cleaner base to reduce overall height |
|
BETTER AIRFLOW! . Morosofs unique radiused air inlet design equalizes air pressure past the boosters for uniform air flow . Radiused air inlet is stamped into air cleaner base to reduce overall height LOW STACKING HEIGHT! • Air Cleaners with 3" element have an overall stacking height above the carburetor lip of only 2-1/2", while 5" filters have a 4-1/2" overall height • Fits all Holley®, CarterR, RochesterR, and EdelbrockR carburetors with 5-1/8" diameter necks & MSDR Atomic EFI |
|
MORE POWER! • Back to back dyno testing proves a gain of nearly 10 horsepower over running no air cleaner at all GREAT LOOKS! • Available accessories including valve covers, breathers and ignition wire sets • Includes matching wing nut |
| PART # | DESCRIPTION |
| 65904 $125.43 * | Racing Air Cleaner, 14" dia. with 3" filter, Powder Coated-Black, PCV adapter included |
| 65905 $157.80 * | Racing Air Cleaner, 14" dia. with 3" filter, Powder Coated-Red, PCV adapter included |
| 65906 $157.80 * | Racing Air Cleaner, 14" dia. with 3" filter, Powder Coated-Blue, PCV adapter included |
| 65910 $82.16 * | Racing Air Cleaner, 14" dia. with 3" filter, Chrome plated steel, hand polished, PCV adapter included |
| PART # | REPLACEMENT PARTS |
| 97080 $21.52 | 3" x 14" Air Cleaner Element |
| 97081 $29.55 | 4" x 14" Air Cleaner Element |
| 97330 $32.25 | 5" x 14" Air Cleaner Element (includes stud) |
|
• Classic Moroso high flow, low stacking height design • Increased horsepower with great fiber design look • Includes wing nut and stud • Fits all Holley®, CarterR, RochesterR, and EdelbrockR carburetors with 5-1/8" diameter necks & MSDR Atomic EFI |
| PART # | DESCRIPTION |
| 65915 * | Racing Air Cleaner, 14" diameter with 3" filter Gray/Black Fiber Design |
| PART # | REPLACEMENT PART |
| 97080 $21.52 | 3" x 14" Air Cleaner Element |
| *Not legal for sale or use on pollution-controlled vehicles unless originally equipped with an open element air cleaner. |
|
AIR CLEANER Raised bottom for 14" x 3" • This air cleaner bottom section converts Moroso and other 14" x 3" air cleaner assemblies to the Moroso "Raised Bottom design" that clears Edelbrock® 4 BBL Carburetors and Holley Carburetors with tall throttle return spring brackets • Features a deep retaining lip that locks the air cleaner element in place • Aluminum with a raw aluminum finish • Can be polished, painted, powder coated or chrome painted for a custom look |
| PART # | DESCRIPTION |
| 97090 $59.20 | Air Cleaner, Raised bottom section for 14" X 3" assemblies |
|
• Flat bottom design raises installed height of air cleaner
for additional sheet metal clearance in race cars such as NASCAR®
Modifieds • 14" diameter Air Cleaners available with 3" or 5" filter elements • Chrome plated steel • Fits Holley®, Carter®, Edelbrock® and Rochester® carburetors |
| PART # | DESCRIPTION |
| 65911 $82.16 * | Flat Bottom Air Cleaner, 14" dia. with 3" filter, chrome, Fits: Holley®, Thermoquad, Quadrajet and similar carburetors with 5-1/8" dia. neck, PCV adapter included |
| 65945 $105.19 * | Flat Bottom Air Cleaner, 14" dia. with 3" filter, chrome, Fits: Holley® 4500 carburetors with 7-5/16" dia. neck |
| 65946 $110.55 * | Flat Bottom Air Cleaner, 14" dia. with 5" filter, chrome. Fits: Holley® 4500 carburetors with 7-5/16" dia. neck |
| PART # | REPLACEMENT PARTS |
| 97080 $21.52 | 3" x 14" Air Cleaner Element (does not includes stud) |
| 97330 $32.25 | 5" x 14" Air Cleaner Element (includes stud) |
|
• Owners of Small Block Chevy powered cars with 2- and 4-bbl.
Holley® carbs with 5-1/8" necks don't have to cut up
their air cleaners to make room for large diameter distributors,
such as HEI • Offset forward by 1-1/2" to clear GM HEI distributors • For IMCA and NASCAR® Modifieds that require air cleaners to be mounted above the hood line, the raised bottom (3/8") design provides an overall height above the carburetor lip of 4-3/4" • For late model stocks that require under-hood air cleaners, the dropped (1-3/4") design provides an overall height above the carburetor lip of 2-3/4" • Finished in Chrome plated top, clear anodized bottom and comes complete with 4" filter elements, one 1/4" -20 and one 5/16" -18 offset stud and three 1/4" -20 and three 5/16" -18 hex nuts |
| PART # | DESCRIPTION |
| 65928 $145.75 * | 14" Offset Air Cleaner with Raised Bottom, 4" element, Chrome Plated Top-Clear, 2- and 4-bbl Holley® |
| PART # | REPLACEMENT PART |
| 97081 $29.55 | 4" x 14" Air Cleaner Element |
|
AIR CLEANERS, RAISED BOTTOM 14" X 3", Raised Bottom • Raised bottom design clears Edelbrock® 4 BBL Carburetors and Holley Carburetors with tall throttle return spring brackets • Air Cleaner top and bottom accept a 14" diameter air cleaner element • Kits include a Moroso 3" tall element • Radiused air inlet design equalizes air pressure past the boosters for uniform air flow • Includes mounting stud, and matching wing nut • Available with a black powder coat or chrome finish top |
| PART # | DESCRIPTION |
| 65912 $126.74 | Air Cleaner Kit, 14" X 3", Raised bottom, Black Powder Coat |
| 65913 $97.20 | Air Cleaner Kit, 14" X 3", Raised bottom, Chrome |
|
11-1/2" and 8-1/2" Diameters • Available in black, red and blue powdercoat and ultra-high luster, hand polished triple-process, chrome plated steel • Matching wing nut included • Fits Holley®, Thermoquad, Quadrajet and similar carburetors with a 5-1/8" diameter neck |
| PART # | DESCRIPTION |
| 66210 $94.43 * | Race/Street Air Cleaner, 11-1/2" diameter with 2-3/8" filter, Chrome plated steel |
| 66303 $105.22 * | Race/Street Air Cleaner, 8-1/2" diameter with 2-3/8" filter, Powder Coated-Black |
| 66304 $133.53 * | Race/Street Air Cleaner, 8-1/2" diameter with 2-3/8" filter, Powder Coated-Red |
| 66305 $133.53 * | Race/Street Air Cleaner, 8-1/2" diameter with 2-3/8" filter, Powder Coated-Blue |
| 66310 $87.70 * | Race/Street Air Cleaner, 8-1/2" diameter with 2-3/8" filter, Chrome plated steel |
| PART # | REPLACEMENT PARTS |
| 97510 $20.17 | Air Cleaner Element. 2-3/8" x 8-1/2" diameter |
| 97520 $22.82 | Air Cleaner Element. 2-3/8" x 11/1/2" diameter |
|
LOW PROFILE AIR CLEANER 16" O.D. • 1-3/4" dropped base to work on carbs with 7-5/16" diameter necks (4500 Series, Dominator, King Demon) • Filter element for harsh racing environments, including Dirt Tracks • Works with 3-1/2", 4", 4-1/2" and 5" tall filter elements • Thick .060" spun aluminum, can be polished, painted or powder coated • Radiused air inlet for maximum air flow • Will work with K&NR 16-1/8", 16-1/4" and 16-3/16" O.D. air filter • Improved filter element retaining lip on base |
| PART # | DESCRIPTION |
| 65920 $214.60 | 16" Low Profile Air Cleaner with dropped bottom, 4" element, for 4500 Series, Dominator, King Demon Carbs |
| PART # | REPLACEMENT PART |
| 97085 $66.03 | 4" x 16" Air Cleaner Element |
|
11-1/2" and 8-1/2" Diameters • Fits carburetors with 5-1/8" neck • Designed for Moroso Air Cleaners and other brands with straight lip • Channel provides extra protection against dust and other harmful elements • Channel creates a maximum seal for carburetor airflow • Made from Buna 70 durometer material • Can be used conventionally on rolled lip air cleaner bases by flipping over |
| PART # | DESCRIPTION |
| 97331 $8.99 | Air Cleaner Base Gasket, Channeled |
|
• When dirt and clay oval tracks turn into "dust bowls",
even the best racing air cleaners can become clogged with dirt
and dust • Made of open cell foam to keep large debris out of the filter element without restricting airflow • Fits snugly around 14" x 5" racing filters • Can be cleaned in the sink or even in the washing machine • Excellent for off-road truck applications • One per pack |
| PART # | DESCRIPTION |
| 65947 $20.24 | Reusable Foam Filter Shield, fits 14" x 5" filters |
|
AIR CLEANER WING NUT • Can be used with any Moroso Air Cleaner • They also match our extra long Valve Cover Wing Nuts to add a look of uniformity to engine compartment • Made to fit only 1/4" -20 studs • Fits most popular air cleaners • One per pack |
| PART # | DESCRIPTION |
| 65820 $10.37 | Air Cleaner Wing Nut, Chrome plated steel |
|
• Available for either single or dual carb applications • Unlike other brands, our Air Pan Kits are designed with a smooth radius at the intake area of the carburetor for improved airflow • Air Pan-to-hood sealing ring is manufactured of fire retardant foam, for added protection • All Air Pans measure 12" x 24" fire retardant foam measures 1-1/2" wide x 4" tall x 60" long |
| PART # | DESCRIPTION |
| 65950 | Carburetor Air Pan Kit, Dual 4-bbl. Holley® carburetors with 5-1/8" neck |
| 65951 $105.23 | Carburetor Air Pan Kit, Dual 4-bbl. Holley® 4500 Dominator carburetors with 7-5/16" neck |
| 65960 $103.75 | Carburetor Air Pan Kit, Single 4-bbl. Holley® carburetors with 5-1/8" neck |
| 65961 $103.75 | Carburetor Air Pan Kit, Single 4-bbl. Holley® 4500 Dominator carburetors with 7-5/16" neck |
| PART # | REPLACEMENT PART |
| 97070 $24.15 | Sealing Foam, 4" x 60" |
|
• Allows Moroso and other air cleaners with 1/4" stud
and wing nut to be used on carburetors with a 5/16" mounting
hole • One end of the adapter features a 5/16" -18 male thread that screws into the carburetor, the other end features a 1/4" -20 female thread that accepts a standard air cleaner mounting stud • Clear zinc plating resists corrosion • Overall length: 7/8" • One per pack |
| PART # | DESCRIPTION |
| 66390 $5.48 | Air Cleaner Stud Adapter, Fits: Holley® H.P. Series, DEMON and other carburetors with 5/16"-18 air cleaner mounting |
| Using advanced gas dynamics and sophisticated noise cancellation acoustics, Moroso engineers have developed the finest and most durable Racing Mufflers for your Exhaust System. Specially engineered spiral baffles divide the exhaust flow into two separate paths, significantly reducing noise levels with minimal backpressure. |
|
• Reduced noise levels with minimal backpressure • These mufflers offer a 5 - 7 db drop over open collectors and the mufflers flow 850 C.F.M |
| PART # | DESCRIPTION |
| 94050 $99.74 | Spiral Flow Racing Muffler, Heavy Duty Steel, 2/5" Inlet/Outlet |
| 94051 $99.74 | Spiral Flow Racing Muffler, Heavy Duty Steel, 3.0" Inlet/Outlet |
| 94052 $99.74 | Spiral Flow Racing Muffler, Heavy Duty Steel, 3/5" Inlet/Outlet |
|
HIGH FLOW POLISHED STAINLESS STEEL MUFFLERS • Reduced noise levels with minimal back pressure • Stainless steel construction makes them durable without compromising the looks |
| PART # | DESCRIPTION |
| 94054 $161.82 | Muffler High Flow, Stainless Steel, 2.5" Inlet/Outlet |
| 94055 $161.82 | Muffler High Flow, Stainless Steel, 3" Inlet/Outlet |
| 94056 $161.82 | Muffler High Flow, Stainless Steel, 3.5" Inlet/Outlet |
|
• Weld-in bung needed when replacing stock exhaust with
aftermarket pipes, headers, etc., not equipped for sensor • M-18 by 1.5 Thread Size |
| PART # | DESCRIPTION |
| 22730 $13.45 | Oxygen Sensor Bung, Mild Steel, Single |
| 22731 $126.74 | Oxygen Sensor Bung, Mild Steel, 10 per pack |
| 22732 $17.46 | Oxygen Sensor Bung, Stainless Steel, Single |
| 22733 $163.20 | Oxygen Sensor Bung, Stainless Steel, 10 per pack |
| PART # | DESCRIPTION |
| 22734 $13.30 | Plug, steel with 17mm hex head, M-18 thread size |
| PART # | ACCESSORIES |
| 22730 $13.45 | Oxygen Sensor Bung, Mild Steel, Single |
| 22731 $126.74 | Oxygen Sensor Bung, Mild Steel, 10 per pack |
| 22732 $17.46 | Oxygen Sensor Bung, Stainless Steel, Single |
| 22733 $163.20 | Oxygen Sensor Bung, Stainless Steel, 10 per pack |
|
HEADER FLANGE KIT • Aluminum plates simplify the task of matching exhaust ports to large tube, dual flange headers on Small Block Chevy engines • Only 3/8" thick to save weight • Includes six plates, enough for one engine |
| PART # | DESCRIPTION |
| 67650 $167.24 | Header Flange Kit, Small Block Chevy |
|
• 1/2" thick, 18" x 24" non-asbestos blanket
can be easily cut to any shape with scissors, and wrapped around
fuel lines, brake lines, dry sump lines, power steering lines,
etc; withstands up to 2300°F • May also be used on firewalls and floor boards to reduce in-car temperature • Made from a silica-based formula that contains no asbestos |
| PART # | DESCRIPTION |
| 80805 $45.79 | Heat Barrier Blanket |
|
. Increases exhaust cycle efficiency • Protects crew members from burns, and prevents starter wires and plug wires from coming into contact with hot header pipes • Reduces engine compartment temperature • Highly pliable for a nice, tight wrap • Made from a silica-based formula that contains no asbestos |
| PART # | REPLACEMENT PARTS |
| 80807 $149.76 | Insulating Header Wrap, 2" x 1/16" x 100' Roll |
| 80808 $83.58 | Insulating Header Wrap, 2" x 1/16" x 50' Roll |
| 80809 $48.42 | Insulating Header Wrap, 1" x 1/16" x 50' Roll |
|
Stainless Steel, 24 Pack • Insulating header wrap has proven itself to increase exhaust cycle efficiency, protect crew members from burns, prevent starter, plug wires from coming in contact with hot header pipes and reduces engine compartment temperature • Installing header wrap and making sure that it stays where it needs to is more problematic. Using a Exhaust Wrap Band Clamp on the beginning and throughout the wrapping process keeps the wrap locked in place for better heat retention and a neater appearance • The low profile, pull through clamps are easier to use than hose clamps and plastic tie wraps can’t hold up to heat like these clamps can • Manufactured out of high grade 304 stainless steel, with a tensile strength of 200 lbs and a temperature rating of over 2500 Degrees • Kit comes with 18 pieces of 14" long clamps for the primary tubes and 6 pieces of 20" long clamps for the collectors, more than enough for a V-8 engine • For ease of installation, use optional Part No. 62284 $26.84 Band Clamp Tightening Tool (sold separately) |
| PART # | DESCRIPTION |
| 80810 | Exhaust Wrap Band Clamp Kit, Stainless steel, 24 pack |
| PART # | AVAILABLE OPTION |
| 62284 $26.84 | Band Clamp Tightening Tool for MOROSO PART NO. 80810, band clamps, or other types of band or boot clamps. |
| PART # | DESCRIPTION |
| 67250 $345.51 | Stud Girdle, use with 7/16" studs and roller rocker arms. Fits: BBC, also fits aftermarket BBC heads with standard rocker arm stud location |
| PART # |
REPLACEMENT PARTS - FOUR PER PACK |
| 67100 $16.02 | U-Bolts, For Stud Girdle, SBC use No. 67050, 67070. |
| 67300 $13.34 | U-Bolt Assembly, Use with No. 67250. |
| 67320 $45.72 | Slotted Head Adjusting Nuts, Use with No. 67250, on exhaust studs |
|
HEX HEAD MOROSO STUD GIRDLE ADJUSTING NUTS • For use with Moroso Stud Girdles • Hex head design allows easier valve adjustments with a set screw providing a positive lock • Fits either stock or roller rockers • Four per pack |
| PART # | DESCRIPTION |
| 67150 $31.90 | Hex Head Adjusting Nuts, fits 3/8" Rocker Studs Use with Nos. 67040 and 67205 |
| 67160 $67.41 | Hex Head Adjusting Nuts, fits 7/16" Rocker Studs Use with Nos. 67045, and 67205, also fits No. 67295, (Exhaust only) |
| 67170 $66.14 * | Hex Head Adjusting Nuts, fits BBC Intakes, Use with No. 67295. |
|
• Redirects oil from pushrod to fulcrum balls, rockers and
springs to provide maximum lubrication and cooling • Extends life of stock valvetrain assembly • Helps eliminate excessive oil accumulation in breather tank when vacuum pump is used • Manufactured from lightweight .100" aluminum • Mounts easily to stock rocker arm studs • Includes mounting hardware • Can be easily adapted to many other applications |
| PART # | DESCRIPTION |
| 67700 $47.10 | Valvetrain Oil Deflector, must use with tall Valve Covers. Polylocks not included Fits: all SBC and Ford 289-302 engines with stamped rocker arms |
|
ABOUT MOROSO VALVE COVERS Many Moroso Valve Covers are manufactured in the tall style. Taller covers may not fit some engine compartments. Power brake boosters and air conditioning boxes may interfere in some applications. Check hood clearance before ordering. Moroso stock height valve covers are recommended in cases where hood clearance and/or accessory clearance is a problem. However, any Moroso valve cover described as "stockheight" or with "built-in baffles" will not clear stud girdles or shaft rocker assemblies. |
|
CHROME PLATED STEEL Fits: SBC 3-1/2" Tall Design • Includes two breather/filler cap grommets and one baffled and one non-baffled PCV grommet |
| PART # | DESCRIPTION |
| 68102 $83.54 * | Valve Covers, Stamped Steel, Chrome Plated, Tall Design, without Baffles |
| PART # | REPLACEMENT PARTS |
| 68770 $6.52 | PCV Grommet |
| 68772 $5.24 | PCV Grommet with Baffle |
| 93020 $56.54 | Perm Align V/C Gasket |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
Fits: SBC 3-1/2" Tall Design with Baffle • Includes two breather/filler cap grommets and one baffled and one non-baffled PCV grommet |
| PART # | DESCRIPTION |
| 68103 $92.95 * | Valve Covers, Stamped Steel, Chrome Plated,Tall Design. Same as no. 68102, but with a baffle in the oil fill hole. These covers will not clear stud girdles or some shaft rocker assemblies |
| PART # | REPLACEMENT PARTS |
| 68770 $6.52 | PCV Grommet |
| 68772 $5.24 | PCV Grommet with Baffle |
| 93020 $56.54 | Perm Align V/C Gasket |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
Fits: SBC Stock Height with Baffle • Includes two breather grommets and one non-baffled PCV grommet |
| PART # | DESCRIPTION |
| 68392 $87.63 * | Valve Covers, Stamped Steel, Chrome Plated, Stock Height, baffle in the oil fill hole, with logo |
| PART # | REPLACEMENT PARTS |
| 68770 $6.52 | PCV Grommet |
| 68772 $5.24 | PCV Grommet with Baffle |
| 93020 $56.54 | Perm Align V/C Gasket |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
STAMPED VALVE COVERS Fits: SBC Powder Coated, 3-1/2" Tall Design • Includes two breather/filler cap grommets and one baffled and one non-baffled PCV grommet |
| PART # | DESCRIPTION |
| 68003 $192.87 * | Valve Covers, Stamped, Powder Coated-Black, Tall Design |
| 68005 $192.87 * | Valve Covers, Stamped, Powder Coated-Blue, Tall Design |
| 68006 $192.87 * | Valve Covers, Stamped, Powder Coated-Red, Tall Design |
| PART # | REPLACEMENT PARTS |
| 68770 $6.52 | PCV Grommet |
| 68772 $5.24 | PCV Grommet with Baffle |
| 93020 $56.54 | Perm Align V/C Gasket |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
Fits: SBC 3-1/2" Tall Design • Packaged two to a set with rubber breather grommets and eight 1-3/4" long studs • Includes two breather/filler cap grommets and one baffled and one non-baffled PCV grommet |
| PART # | DESCRIPTION |
| 68401 $217.15 * | Valve Covers, Die-Cast Aluminum, Polished Finish with Moroso logo, Tall Design |
| 68405 $210.44 * | Valve Covers, Die-Cast Aluminum, Polished Finish without Moroso logo, Tall Design |
| 68411 $211.84 * | Valve Covers, Die-Cast Aluminum, Black Epoxy Finish with Moroso logo, Tall Design |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 97341 $6.24 | Filler Cap Breather Grommet, .095" |
| 68831 $60.56 | Stud Kit, V/C, Bullet Nose, 12 Pt. Nut |
| 93020 $56.54 | Perm Align V/C Gasket |
| PART # | REPLACEMENT PARTS |
| 68770 $6.52 | PCV Grommet |
| 68772 $5.24 | PCV Grommet with Baffle |
| 97021 | Wing Nut Studs, 1-3/4" |
| 97340 $6.24 | Breather/Filler Cap Grommets |
| PART # | DESCRIPTION |
| 68365 $298.26 * | Valve Covers, Filtered Breather Set, Polished Die-Cast Aluminum with Moroso logo, Tall Design, two breather tubes, 2-3/8" apart, welded to the radiator end of the driverfs side valve cover |
| 68370 $283.37 * | Valve Covers, Filtered Breather Set, Polished Die-Cast Aluminum with Moroso logo, Tall Design, two breather tubes welded to one cover |
| 68371 $329.35 * | Valve Covers, Filtered Breather Set, Black Epoxy finish with Moroso logo, Die-Cast Aluminum, Tall Design, two breather tubes welded to one cover |
| 68374 $286.11 * | Valve Covers, Filtered Breather Set, Polished Die-Cast Aluminum without Moroso logo, Tall Design, two breather tubes welded to one cover |
| 68380 $373.77 * | Valve Covers, Filtered Breather Set, Polished Die-Cast Aluminum with Moroso logo, Tall Design, two breather tubes welded to each cover |
| 68381 $386.02 * | Valve Covers, Filtered Breather Set, Black Epoxy finish with Moroso logo, Die-Cast Aluminum, Tall Design, two breather tubes welded to each cover |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 97341 $6.24 | Filler Cap Breather Grommet, .095" |
| 68831 $60.56 | Stud Kit, V/C, Bullet Nose, 12 Pt. Nut |
| PART # | REPLACEMENT PARTS |
| 68811 $25.53 | Filtered Breathers 180° |
| 68812 $25.53 | Hood Filtered Breathers (for early no. 68370, with 1-1/2" O.D. tubes) |
| 93021 $78.10 | Perm Align V/C Gasket |
| 97020 $10.08 | Studs - 1-3/4" long |
|
Fits: SBC With Crossover Breather Tube 3/5" Tall without Breather • Includes crossover breather tube, two breathers with chrome plated hoods, hoses and clamps for a simple, bolt-on installation • Ideal for Sprint Cars and other Oval Track applications |
| PART # | DESCRIPTION |
| 68385 $411.62 * | Valve Covers, Die-Cast Aluminum with Crossover Breather Tube, Polished Finish with Moroso logo, Tall Design |
| PART # | REPLACEMENT PARTS |
| 68811 $25.53 | Filtered Breathers |
| 93021 $78.10 | Perm Align V/C Gasket |
| 97020 $10.08 | Studs, 1-3/4" long |
|
FABRICATED ALUMINUM, RIGID RAIL Fits: SBC cylinder heads including 18°, 23° 4" Tall at peak • Fabricated entirely from superior quality aluminum, ultra lightweight • Tall enough to clear all popular rocker combinations • Mounting is through tubes welded diretly to the valve covers to help maintain gasket-rail flatness and to prevent leaks • Mounting fasteners included |
| PART # | DESCRIPTION |
| 68335 $552.07 * | Valve Covers, Fabricated Aluminum, Rigid Rail, fits all SBCcylinder heads |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
|
93020 $56.54 Or 93021 $78.10 |
Perm Align V/C Gasket |
| 97341 $6.24 | Filler Cap Breather Grommet, .095" |
| PART # | REPLACEMENT PART |
| 97346 $7.65 | .47" x 19",Washers, Aluminum with Neoprene Seal |
|
FABRICATED ALUMINUM BILLET RAIL, POCKETS Fits: SBC cylinder heads including 18°, 23° 3.38" Tall • Fabricated from superior quality aluminum, ultra lightweight • One-piece billet rail is machined to ensure a precision flat surface for superior sealing • Tall enough to clear all popular rocker combinations • Air-tight sealing allows the engine to pull greater vacuum for improved ring seal and power • Notched at each mounting location with socket-sized clearances for quick installation and removal • Mounting fasteners included |
| PART # | DESCRIPTION |
| 68326 $658.80 * | Valve Covers, Fabricated Aluminum, Logo |
| 68328 $494.05 * | Valve Covers, Fabricated Aluminum, No Logo |
|
93020 $56.54 Or 93021 $78.10 |
Perm Align V/C Gasket |
| PART # | REPLACEMENT PART |
| 97035 $32.27 | Nuts, 12 Pt. |
|
FABRICATED ALUMINUM BILLET RAIL, POCKETS With Valve Spring Oilers Fits: SBC cylinder heads including 18°, 23° 4" Tall • Fabricated entirely from superior quality aluminum, ultra-lightweight • Custom-built for Oval Track Racing/Offshore Boat Racing • Built-in oiling system keeps valve springs running cool for extended life, especially when subjected to long races • An oil regulating jet located at the inlet fitting can be drilled to suit individual oil flow requirements • -4AN male fitting on each cover allows convenient plumbing of oil supply lines • One-piece billet rail with machined gasket recess and bosses holds gasket captive when installing and eliminates leaks • Mounting hardware included |
| PART # | DESCRIPTION |
| 68329 * | Valve Covers, Fabricated Aluminum, With Valve Spring Oilers, Billet Rail. Use Fel-Pro Gasket No. 1644 or Moroso Part no. 93021. |
| PART # | REPLACEMENT PART |
| 97035 $32.27 | Nuts, 12 Pt. |
|
Fits: SBC, 13 To 23 ° Cylinder Heads • Fits Small Block Chevy with 13 to 23 Degree cylinder heads with the valves in the conventional location • Each valve cover is CNC machined from a billet aluminum bar • The end result is that each valve cover weighs 1.69 lbs without sacrificing strength • Airtight sealing allows the engine to pull greater vacuum for improved ring seal and power • Black anodized finish • Designed for Sprint Cars but works in other applications that require strong lightweight valve covers |
| PART # | DESCRIPTION |
| 68050 $959.77 * | Valve Covers, Billet Aluminum, SBC Fits 13 To 23 Deg. Cylinder Heads, Billet, Black Anodized Finish |
| PART # | REPLACEMENT PART |
| 93020 $56.54 Or 93021 $78.10 | Perm Align V/C Gasket |
|
FABRICATED ALUMINUM, BILLET RAIL Fits: SBC center bolt cylinder heads 4" Tall • Fabricated entirely from superior quality aluminum, ultra-lightweight • Tall enough to clear all popular rocker combinations • Mounting is through tubes welded directly to the valve covers to help maintain gasket-rail flatness and to prevent leaks • One-piece billet aluminum rail is CNC machined to ensure a precision flat surface for superior sealing • Mounting fasteners included • Use OEM or aftermarket gaskets |
| PART # | DESCRIPTION |
| 68025 $678.98 * | Valve Covers, Fabricated Aluminum, Logo |
| 68028 $541.24 * | Valve Covers, Fabricated Aluminum, No Logo |
| 68026 $730.26 * | Valve Covers, Fabricated Aluminum, Logo, two breather tubes welded to driver side cover with Filtered Breather |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 97341 $6.24 | Filler Cap Breather Grommet, .095" |
| PART # | REPLACEMENT PARTS |
| 68811 $25.53 | Filtered Breathers 180¢ª Hood |
| 97345 $7.65 | .62 " x .19",Washers, Aluminum with Neoprene Seal |
|
For F, B, & Y Body Fits: SBC center bolt cylinder heads 2.5" Tall • Fits Camaro/Firebird ’93-’97, Caprice/Impala SS ’94-’96 and Corvette ’92-‘96 • Valve covers are notched to clear factory alternators and brackets • One-piece billet aluminum rail is CNC machined to ensure a precision flat surface for superior sealing • Airtight sealing allows the engine to pull greater vacuum for improved ring seal and power • Use OEM or aftermarket gaskets • Features oil fill hole with billet aluminum cap, port for PCV • Mounting hardware included |
| PART # | DESCRIPTION |
| 68027 * |
Valve Covers, GM Center bolt Aluminum for F, B & Y Body |
| PART # | REPLACEMENT PARTS |
| 97345 $7.65 | .62 " x .19",Washers, Aluminum with Neoprene Seal |
|
GM LT1/LT4//L86 BILLET ALUMINUM VALVE COVERS WITHOUT
COIL MOUNTS Fits: GM LTI/LT4/L86 6.2L cylinder heads • 1-1/2" tall to clear most engine accessories and aftermarket valve train assemblies • Valve covers are designed for the coils to be mounted remotely • Each valve cover is CNC machined from a solid billet aluminum bar • Cylinder head mounting area has an o-ring groove that accepts GM#12619787 Valve Cover O-Ring Gasket • Even though these valve covers are light in weight, they are thick enough for the engine builder to be able to add fittings at the top and ends • The covers can be polished, chromed, powder coated or left as-is for a race look |
| PART # | DESCRIPTION |
| 68480 $661.37 * | Valve Covers, Billet Aluminum, GM LTI/LT4/L86 without coil mounts |
|
GM LS SERIES, ALL BILLET ALUMINUM VALVE COVERS Fits: GM LS Series Stock and Aftermarket Cylinder Heads • Each valve cover is CNC machined from a solid billet aluminum bar • Available in 4 different versions - 2.5" tall to clear most aftermarket valvetrains without coil mounts - 2.5" tall to clear most aftermarket valvetrains with integral coil pack mounts that accept LS2, LS3, LS7 & L98 style coils - 1.5" tall to clear most engine accessories without coil mounts - 1.5" tall to clear most engine accessories with integral coil pack mounts that accept LS2, LS3, LS7 & L98 style coils • Cylinder head mounting area has an O-Ring groove that accepts Moroso No. 93025, or GM Gasket • One cover features a oil fill with a CNC machined cap with O-ring • Even though these valve covers are light in weight, they are thick enough for the engine builder to be able to add fittings at the top and ends • The covers can be polished, chromed, powder coated or left as-is for a race look |
| PART # | DESCRIPTION |
| 68470 $1,158.11 * | Valve Covers, Billet Alum., GM LS Series, 2.5" tall with coil mounts |
| 68471 $997.56 * | Valve Covers, Billet Alum., GM LS Series, 2.5" tall w.o. coil mounts |
| 68472 $943.53 * | Valve Covers, Billet Alum., GM LS Series, 1.5" tall with coil mounts |
| 68473 $880.15 * | Valve Covers, Billet Alum., GM LS Series, 1.5" tall w.o. coil mounts |
|
MOROSO ULTRA 40 IGNITION WIRE SETS FOR MOROSO GM LS SERIES
BILLET ALUMINUM VALVE COVERS You have the Moroso all billet aluminum GM LS valve covers, why use any other spark plug wire than the Moroso Ultra 40 Sleeved sets that were designed to be used with these valve covers? |
|
• Part No. 73845 $187.45 is for the Moroso Part nos. 68471
$997.56 and 68473 $880.15 All Billet Aluminum Valve Covers that
use the Moroso Part nos. 72397 $360.40 & 72398 $357.60 Coil
Mount Brackets • Part No. 73846 $187.45 is for the Moroso Part nos. 68470 $1,158.11 and 68472 $943.53 All Billet Aluminum Valve Covers that have the integral coil pack mounts that accept LS2, LS3, LS7, & L98 style coils • Wire Sets are constructed out of Moroso ULTRA 40, 7 mm Dia. Ignition Wire with 40 ohms of resistance per foot • The black wire sets are sleeved which extends spark plug life and protects against exhaust header heat, chaffing and contaminants • Sleeving also adds extra dielectric strength which is wire’s ability to not to be affected by outside electrical pulses • Each wire is terminated with heavy duty, high temperature, easy-pull/positive engagement spark plug boots and on the other end with matching coil boots • Complete, ready to install |
| PART # | DESCRIPTION |
| 73845 $187.45 | Wire Set, Ultra 40, Sleeved in Black, for Moroso Part nos. 68471, and 68473. |
| 73846 $187.45 | Wire Set, Ultra 40, Sleeved in Black, for Moroso Part nos. 68470, and 68472. |
|
COIL MOUNT BRACKET KIT, GM LS SERIES COIL MOUNT BRACKET KIT,
FOR MOROSO 68471/68473 VALVE COVERS • These Coil Brackets can used to relocate LS Coils between the top of the valve cover and the intake • Designed to be used with Moroso valve covers but can be drilled to be used with other valve covers or to remote mount coils in a different location • Two versions available; One for LS1/LS6 Coils & the Second for LS2, LS3, LS7, L92, L99 Coils • When used with Moroso valve covers, the valve cover can be removed and installed without disturbing the coils or brackets • Kit includes black anodized aluminum brackets and metric hardware, one kit does one LS engine |
| PART # | DESCRIPTION |
| 72397 $360.40 | Coil Mount Bracket, GM LS Series for 68471/68473, LS1, LS6 Coils |
| 72398 $357.60 | Coil Mount Bracket, GM LS Series for 68471/68473, LS2, LS3, LS7, L92, L99 Coils |
|
CHROME PLATED STEEL Tall Design, Without & With Baffle Fits: BBC 3.5" Tall • Includes two breather/filler cap grommets and one baffled and one non-baffled PCV grommet |
| PART # | DESCRIPTION |
| 68112 $106.58 * | Valve Covers, Stamped Steel, Chrome Plated, Tall Design without Baffle |
| 68113 $122.69 * | Valve Covers, Stamped Steel,Chrome Plated, Tall Design with built-in Baffle |
| PART # | ACCESSORIES |
| 68770 $6.52 | PCV Grommet |
| 68772 $5.24 | PCV Grommet with Baffle |
| 93040 $90.34 | Perm Align V/C Gasket |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
Fits: BBC 3.5" Tall • Includes two breather/filler cap grommets and one baffled and one non-baffled PCV grommet • Mounting fasteners included |
| PART # | DESCRIPTION |
| 68425 $282.03 * | Valve Covers, Die-Cast Aluminum Polished Finish without Moroso logo, Tall Design |
| 68429 $264.40 * | Valve Covers, Cast Aluminum, Big Block Chevy black wrinkle finish |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 68562 $16.13 | Valve Cover, Acorn Nuts for BBC |
| 93040 $90.34 | Perm Align V/C Gasket |
| 97341 $6.24 | Filler Cap Breather Grommet, .095” |
| PART # | REPLACEMENT PARTS |
| 68770 $6.52 | PCV Grommet |
| 68772 $5.24 | PCV Grommet with Baffle |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
CAST ALUMINUM VALVE COVERS - FIBER DESIGN Fits: BBC 3.5" Tall • Extra tall design clears most stud girdles and rocker combinations • Includes one baffled and one non-baffled PVC grommets • Sold in pairs, includes all mounting hardware |
| PART # | DESCRIPTION |
| 68426 $387.37 * | Cast Aluminum Valve Covers, Gray/Black Fiber Design |
| PART # | ACCESSORIES |
| 68562 $16.13 | Valve Covers, Acorn Nuts for BBC |
| 93040 $90.34 | Perm Align V/C Gasket |
|
CAST ALUMINUM RIBBED VALVE COVERS Fits: BBC 3.5" Tall • Constructed out of cast aluminum with a MOROSO Logo. • Includes two breather/filler cap grommets and one baffled and one non-baffled PCV grommet • Includes mounting hardware |
| PART # | DESCRIPTION |
| 68420 $292.90 * | Valve Covers, Ribbed, Cast Aluminum, Big Block Chevy with a polished finish |
| 68432 $313.15 * | Valve Covers, Ribbed, Cast Aluminum, Big Block Chevy with a black powder coat finish |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 68562 $16.13 | Valve Cover, Acorn Nuts for BBC |
| 93040 $90.34 | Perm Align V/C Gasket |
| 97341 $6.24 | Filler Cap Breather Grommet, .095” |
| PART # | REPLACEMENT PARTS |
| 68770 $6.52 | PCV Grommet |
| 68772 $5.24 | PCV Grommet with Baffle |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
Fits: BBC cylinder heads including Bowtie heads Part No. 10051128
3.385" Tall • Fabricated entirely from superior quality aluminum, ultra-lightweight • Tall enough to clear all rocker combinations • Fasteners are included with each set and mount through tubes welded directly to the valve covers to help maintain gasket-rail flatness and to prevent leaks • Call our Technical Services Department for custom applications not listed below |
| PART # | DESCRIPTION |
| 68333 $560.18 * | Valve Covers, Fabricated Aluminum, 3.5" Tall, Rigid Rail, Weight: 3.5 lbs. each |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095” |
| 68773 $5.21 | PCV Grommet/Baffle, .095” |
| 68776 $6.89 | Breather Grommet/Baffle, .095” |
| 93040 $90.34 | Perm Align V/C Gasket |
| 97341 $6.24 | Filler Cap Breather Grommet, .095” |
| PART # | REPLACEMENT PART |
| 97345 $7.65 | .62” x .19”,Washers, Aluminum with Neoprene Seal |
|
FABRICATED ALUMINUM, BILLET RAIL Fits: BBC & aftermarket cylinder heads with stock BBC bolt pattern, clears Jesel, T&D Rocker Shaft Assemblies 3" Tall, clears Jesel style rockers & allows for greater hood clearance • 3/8" billet rail CNC machined • Steel inserts pressed into all mounting holes to eliminate galling after removal and installation • CNC machined after welding to ensure airtight sealing • Mating of billet rail to valve cover is done with a smooth transition on exhaust side to eliminate trapped oil • Notched at each mounting location with socket-sized clearances for quick removal and installation • Will not clear stud girdles |
| PART # | DESCRIPTION |
| 68345 $699.18 * | Valve Covers, Fabricated Aluminum, 3" Tall, Logo |
| 68353 $610.07 * | Valve Covers, Fabricated Aluminum, 3" Tall, No Logo |
| 68356 $750.49 * | Valve Covers, Fabricated Aluminum Installed with Part No. 22635, .12AN Pos Seal Fitting (included) |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 68831 $60.56 | Stud Kit, V/C, Bullet Nose, 12 Pt. Nut |
| 93040 $90.34 | Perm Align V/C Gasket |
| 97341 $6.24 | Filler Cap Breather Grommet, .095” |
|
FABRICATED ALUMINUM, MARINE, DIRT LATE MODEL Fits: BBC, symmetrical-port Bowtie cylinder heads and Stock BBC heads, clears Jesel, T&D Rocker Shaft Assembly 3.5" Tall, clears Jesel style rockers & allows for greater hood clearance • 3/8" billet rail CNC machined • Steel inserts pressed into all mounting holes to eliminate galling after removal and installation • CNC machined after welding to ensure airtight sealing • Mating of billet rail to valve cover is done with a smooth transition on exhaust side to eliminate trapped oil • Notched at each mounting location with socket-sized clearances for quick removal and installation • Will not clear stud girdles |
| PART # | DESCRIPTION |
| 68350 $740.99 * | Valve Covers, Fabricated Aluminum, Billet Rail, swept back design engineeered to clear most marine wet mainfolds, |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 68831 $60.56 | Stud Kit, V/C, Bullet Nose, 12 Pt. Nut |
| 93040 $90.34 | Perm Align V/C Gasket |
| 97341 $6.24 | Filler Cap Breather Grommet, .095” |
|
FABRICATED ALUMINUM, BILLET RAIL Fits: Big Block GM and Aftermarket Cylinder Heads with stock GM bolt pattern. Clears Jesel and T&D Rocker Shaft Assemblies |
|
• Fabricated entirely from superior quality aluminum, ultra
lightweight • One-piece billet rail is CNC machined to ensure a precision flat surface for superior sealing • Mating of the billet rail to the valve cover is done with a smooth transition, eliminating trapped oil and spills when removing the cover 3" tall, For Greater Hood clearance |
| PART # | DESCRIPTION |
| 68457 $611.50 * | Valve Covers, Fabricated Aluminum, pockets on both exhaust and intake sides, Logo |
| 68479 $543.96 * | Valve Covers, Fabricated Aluminum, pockets on both exhaust and intake sides, No Logo |
| 68458 $611.50 * | Valve Covers, Fabricated Aluminum, tubes on intake side and pockets on exhaust side, Logo |
| 68481 $560.13 * | Valve Covers, Fabricated Aluminum, tubes on intake side and pockets on exhaust side, No Logo |
| PART # | DESCRIPTION |
| 68459 $615.40 * | Valve Covers, Fabricated Aluminum, pockets on both exhaust and intake side, Logo |
| 68482 $546.64 * | Valve Covers, Fabricated Aluminum, pockets on both exhaust and intake side, No Logo |
| 68460 $623.61 * | Valve Covers, Fabricated Aluminum, tubes on intake side and pockets on exhaust side, Logo |
| 68486 $570.93 * | Valve Covers, Fabricated Aluminum, tubes on intake side and pockets on exhaust side, No Logo |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 68831 $60.56 | Stud Kit, V/C, Bullet Nose, 12 Pt. Nut |
| 93040 $90.34 | Perm Align V/C Gasket |
| 97035 $32.27 | Nuts, 12 Pt |
| 97341 $6.24 | Filler Cap Breather Grommet, .095” |
|
ALL BILLET ALUMINUM Fits: BBC, symmetrical-port Bowtie cylinder heads and Stock BBC heads, clears Jesel, T&D Rocker Shaft Assembly 3" Tall • Each valve cover is CNC machined from a solid billet aluminum bar • The end result is that each valve cover weighs 3.9 lbs with out sacrificing strength • Airtight sealing allows the engine to pull greater vacuum for improved ring seal and power • 3” Tall, clears Jesel style rockers & allows for greater hood clearance • Designed with a broad, flat surface for engine builder engraving, the covers can be polished, chromed, powder coated or left as-is for a race look |
| PART # | DESCRIPTION |
| 68469 $1,173.06 * | Valve Covers, , BBC Fits symmetrical-port Bowtie and Stock BBC heads |
| PART # | ACCESSORIES |
| 68831 $60.56 | Stud Kit, V/C, Bullet Nose, 12 Pt. Nut |
| 93040 $90.34 | Perm Align V/C Gasket |
|
FFABRICATED ALUMINUM, BILLET RAIL Fits: Dart Big Chief ll, 11 Degree and 14 Degree Style Cylinder Heads 3" Tall • Fabricated entirely from superior quality aluminum, ultra lightweight • One-piece billet rail is CNC machined to ensure a precision, flat surface for superior sealing • Airtight sealing allows the engine to pull greater vacuum for improved ring seal and power |
| PART # | DESCRIPTION |
| 68463 $668.13 * | Valve Covers, Fabricated Aluminum, Dart Big Chief II, 11 Degree and 14 Degree Style Cylinder Heads |
| PART # | ACCESSORIES |
| 68831 $60.56 | Stud Kit, V/C, Bullet Nose, 12 Pt. Nut |
| 93045 $78.18 | Perm Align V/C Gasket |
|
Fits: BBC with Brodix PB2005, Brodix PB1200, Brodix 1202 and
Sonny 14.5 cylinder heads 3" Tall • Fabricated entirely from superior quality aluminum, ultra-lightweight • One-piece billet rail is CNC machined to ensure a precision flat surface for superior sealing • Airtight sealing allows the engine to pull greater vacuum for improved ring seal and power |
| PART # | DESCRIPTION |
| 68455 $603.26 * | Valve Covers, Fabricated Aluminum, Billet Rail |
| PART # | ACCESSORIES |
| 68831 $60.56 | Stud Kit, V/C, Bullet Nose, 12 Pt. Nut |
|
Fits: BBC with Dart Big Chief and Brodix Big Duke Style cylinder
heads. Does not fit Dart Big Chief ll, 11 Deg. cylinder heads.
Clears Jesel and T&D Rocker Shaft assemblies 3" Tall • Fabricated entirely from superior quality aluminum, ultra-lightweight • One-piece billet rail is CNC machined to ensure a precision flat surface for superior sealing • Airtight sealing allows the engine to pull greater vacuum for improved ring seal and power |
| PART # | DESCRIPTION |
| 68456 $608.77 * | Valve Covers, Fabricated Aluminum, pockets on intake and exhaust side |
| PART # | ACCESSORIES |
| 68831 $60.56 | Stud Kit, V/C, Bullet Nose, 12 Pt. Nut |
| 93045 $78.18 | Perm Align V/C Gasket |
|
FAb. BRODIX SR20/DART PRO1 20 DEG. ALUM. BILLET RAIL VALVE COVERS Fits: Brodix SR20/Dart Pro1 20 Deg. Cylinder Heads 3" Tall • Fabricated entirely from superior quality aluminum, ultra lightweight • One-piece billet rail is CNC machined to ensure a precision flat surface for superior sealing • Mating of the billet rail to the valve cover is done with a smooth transition, eliminating trapped oil and spills when removing the cover • Designed with a broad, flat surface for engine builder engraving, the covers can be polished, chromed, powder coated or left as-is for a race look |
| PART # | DESCRIPTION |
| 68483 $628.95 * | Valve Cover, Fab. Alum., Billet Rail for Brodix SR20/Dart Pro1 Cylinder Heads, tubes on intake side and pockets on exhaust side |
| 68484 $632.99 * | Valve Cover, Fab. Alum., Billet Rail for Brodix SR20/Dart Pro1 Cylinder Heads, tapered on exhaust side to clear Dirt Late chassis |
| 68487 $615.40 * | Valve Cover, Fab. Alum., Billet Rail for Brodix SR20/Dart Pro1 Cylinder Heads, pockets on both intake and ehaust side |
| PART # | ACCESSORIES |
| 68831 $60.56 | Stud Kit, V/C Bullet Nose, 12 Pt. Nut |
| PART # | DESCRIPTION |
| 68161 $94.39 * | Valve Covers, Stamped Steel, Chrome Plated, Tall Design with Baffles |
| PART # | ACCESSORIES |
| 93050 $61.92 | Perm Align V/C Gasket |
| PART # | REPLACEMENT PART |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
Fits: S.B. Chrysler, 273, 318, 340, 360 and W2 heads 3.750" Tall • Fabricated entirely from one-piece superior quality aluminum, ultralightweight • One-piece billet rail is CNC machined to ensure a precision flat surface for superior sealing • Airtight sealing allows the engine to pull greater vacuum for improved ring seal and power • Mating of the billet rail to the valve cover is done with a smooth transition, eliminating trapped oil and spills when removing the cover • Notched at each mounting location with socket-sized clearances for quick removal and installation • Tall enough to clear most rocker combinations • Fasteners Included |
| PART # | DESCRIPTION |
| 68310 $693.70 * | Valve Covers, Fabricated Aluminum, Billet Rail, |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 93050 $61.92 | Perm Align V/C Gasket |
| 97341 $6.24 | Filler Cap Breather Grommet, .095" |
| PART # | REPLACEMENT PART |
| 97035 $32.27 | Nuts, 12 Pt. |
|
ALL BILLET ALUMINUM Fits: Chrysler 5.7/6.1/6.4 Hemi 2.05" Tall • Make your Hemi engine look like it deserves the Hemi name • Each 4 lb. valve cover is CNC machined from a 34 lb. solid billet aluminum bar • Fits both early and late 5.7, 6.1 and 6.4 heads • Must use 2006-up 5.7, 6.1 or 6.4 coil packs • The end result is a lightweight, strong cover that has a precision flat surface for superior sealing • Covers are designed to work with stock coil packs, gaskets and fasteners • Taller for aftermarket valve train assemblies • Airtight sealing allows the engine to pull greater vacuum for improved ring seal and power • Available in two finishes; raw machined billet finish or black anodized finish with machined ribs |
| PART # | DESCRIPTION |
| 68467 $1,586.25 * | Valve Covers, Billet Aluminum, Raw Machined Billet Finish |
| 68468 $1,659.10 * | Valve Covers, Billet Aluminum, Anodized Black with machined ribs |
| PART # | DESCRIPTION |
| 68181 $121.34 * | Valve Covers, Stamped Steel, Chrome Plated, Tall Design with Baffles |
| PART # | ACCESSORIES |
| 93055 $63.26 | Perm Align V/C Gasket |
| PART # | REPLACEMENT PART |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
• Each 6.8 lb valve cover is CNC machined from a 112 lb
Solid Billet Aluminum Bar • Designed to work with Manton Rockers • Designed to be used with Large Plug, 8" Long, Spark Plug Tube Manton Part No. RA0255 • Even though these valve covers are light in weight, they are thick enough for the engine builder to be able to add fittings at the top and ends • The covers can be polished, chromed, powder coated or left as-is for a race look |
| PART # | DESCRIPTION |
| 68490 * | Valve Covers, Billet Aluminum, BME Hemi w/Manton Rockers |
|
CHROME PLATED STEEL Fits: Ford 221-302 & 351W 3.5" Tall • Includes two breather/filler cap grommets and one non-baffled PCV grommet |
| PART # | DESCRIPTION |
| 68201 $95.69 * | Valve Covers, Stamped Steel, Chrome Plated, Tall Design Baffles under openings |
| 68202 $95.69 * | Stamped Steel Valve Covers, Chrome Plated, Tall Design without Baffles |
| PART # | ACCESSORIES |
| 93060 $71.39 | Perm Align V/C Gasket |
|
Fits: Ford 260-302 & 351W 3.5" Tall • Includes two breather/filler cap grommets and one non-baffled PCV grommet |
| PART # | DESCRIPTION |
| 68210 $95.69 * | Valve Covers, Stamped Steel, Chrome Plated, Tall Design, without logo, with Baffles |
| PART # |
REPLACEMENT PARTS FOR NOS. 68201, 68202, 68210, 68770, PCV Grommet |
| 97340 $6.24 | Breather/Filler Cap Grommets |
| PART # | ACCESSORIES |
| 93060 $71.39 | Perm Align V/C Gasket |
|
• Brilliant hand polished finish • Die-casting process is far more precise and results in a blemishfree surface without porosity • Extra tall design clears most stud girdles and rocker combinations • Inside cover is pilot notched, making it easy to cut out openings for a PCV Valve, breather, or oil filler cap; includes grommets |
| PART # | DESCRIPTION |
| 68450 $194.32 * | Valve Covers, Die-Cast Aluminum Ford 221, 260, 289, 302 (5.0L) & 351W |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 93060 $71.39 | Perm Align V/C Gasket |
| 97341 $6.24 | Filler Cap Breather Grommet, .095" |
|
• Tall enough to clear most aftermarket valvetrain assemblies
and stud girdles • Polished aluminum finish • 1.22" fill hole included in each cover • Includes PCV grommet and breather grommet |
| PART # | DESCRIPTION |
| 68444 * | Valve Covers, Polished Aluminum, SBF |
| PART # | ACCESSORIES |
| 93060 $71.39 | Perm Align V/C Gasket |
|
FABRICATED ALUMINUM, BILLET RAIL Fits: Ford 302/351W stock and aftermarket cylinder heads 2.75" Tall to clear most popular rocker combinations including Jesel & T&D Shaft rockers • Replaces Moroso No. 68325 • Fabricated entirely from superior quality aluminum, ultralightweight • One piece billet rail is CNC machined to ensure a precision flat surface for superior sealing • Airtight sealing allows the engine to puller greater vacuum for improved ring seal and power • Notched at each mounting location with socket-sized clearancesfor quick removal and installation • Fasteners included |
| PART # | DESCRIPTION |
| 68475 $560.13 * | Valve Covers, Fabricated Aluminum, Ford 302/351W with Billet Rail |
| PART # | ACCESSORIES |
| 93060 $71.39 | Perm Align V/C Gasket |
|
Fits: Ford 302/351W stock and aftermarket cylinder heads 2.875"
tall to clear most popular rocker combinations including Jesel
& T&D Shaft rockers • Each valve cover is CNC machined from a solid billet aluminum bar • Precision flat mounting rail surface for airtight sealing allowing the engine to pull greater vacuum for ring seal and power • Even though these valve covers are light in weight, they are thick enough for the engine builder to be able to add fittings at the top and ends • The covers can be polished, chromed, powder coated or leftas-is for a race look |
| PART # | DESCRIPTION |
| 68474 $1,032.70 * | Valve Covers, Billet Aluminum, Ford 302/351W |
| PART # | ACCESSORIES |
| 68831 $60.56 | Stud Kit, V/C, Bullet Nose, 12 Pt. Nut |
| 93060 $71.39 | Perm Align V/C Gasket |
|
FABRICATED ALUMINUM, BILLET RAIL Fits: Ford 4.6 & 5.4 Three Valve Engines 3.971" Tall at Cam Cover, 3.674" Tall at the main body . Fabricated entirely from superior quality aluminum, ultra lightweight • One piece billet aluminum rail is CNC machined for superior sealing • Bright aluminum finish matches the Moroso tanks and other under hood accessories or can be polished, chrome plated, etc. for a custom look • These valve covers are a direct bolt in for 2005 - 2010 Mustangs and feature a oil fill hole with billet aluminum cap, ports for PCV and vent lines • Features stand offs for factory wiring, coil mounting, and provisions for factory cam timing solenoids • Airtight sealing allows the engine to pull greater vacuum for improved ring seal and power • 3/8" billet rail with machined to accept OEM gasket • Includes mounting hardware, PCV and fitting |
| PART # | DESCRIPTION |
| 68388 * | Valve Covers, Fabricated Aluminum, Ford 4.6 & 5.4, Three Valve |
|
Fits: Ford 4.6/5.4L 11 Bolt cylinder heads 4.225" Tall at
Cam Cover, 3.110" Tall main body • Fabricated entirely from superior quality aluminum, ultra-lightweight • One piece billet rail is CNC machined to ensure a precision flat surface for superior sealing • Mating of the billet rail to the valve cover is done with a smooth transition, eliminating trapped oil and spills when removing the cover • Tall enough to clear most popular rocker combinations • Fasteners included • Comes with knurled billet oil filler cap and uses stock style gaskets |
| PART # | DESCRIPTION |
| 68389 $931.39 * | Valve Covers, Fabricated Aluminum, SBF Modular |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 97341 $6.24 | Filler Cap Breather Grommet, .095" |
|
FABRICATED ALUMINUM, BILLET RAIL Fits: Ford FE 3.5" Tall • Fabricated entirely from superior quality aluminum, ultra-lightweight • One-piece billet rail is CNC machined to ensure a precision flat surface for superior sealing • Airtight sealing allows the engine to pull greater vacuum for improved ring seal and power |
| PART # | DESCRIPTION |
| 68461 $703.23 * | Valve Covers, Fabricated Aluminum, Billet Rail, 3.5" Tall |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 97341 $6.24 | Filler Cap Breather Grommet, .095" |
| PART # | DESCRIPTION |
| 68348 $720.82 * | Valve Covers, Fabricated Aluminum, Billet Rail, 2.5" Tall |
| 68349 $703.27 * | Valve Covers, Fabricated Aluminum, Billet Rail, 3.5" Tall |
| PART # | ACCESSORIES |
| 68771 $6.24 | PCV Grommet, .095" |
| 68773 $5.21 | PCV Grommet/Baffle, .095" |
| 68776 $6.89 | Breather Grommet/Baffle, .095" |
| 93065 $66.04 | Perm Align V/C Gasket |
| 97341 $6.24 | Filler Cap Breather Grommet, .095" |
|
CHROME PLATED STEEL Fits: Pontiac 301-455 3.5" Tall Design with Baffle • Includes two breather/filler cap grommets and one baffled and one non-baffled PCV grommet |
| PART # | DESCRIPTION |
| 68281 $107.80 * | Valve Covers, Stamped Steel, Chrome Plated, Tall Design with Baffle |
| PART # | REPLACEMENT PARTS |
| 68770 $6.52 | PCV Grommet |
| 68772 $5.24 | PCV Grommet with Baffle |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
PERM-ALIGN VALVE COVER GASKETS • Specially designed gaskets are manufactured from 40 durometer silicone, molded over and vulcanized to a rigid steel frame • The extra-strength design will not leak, blow out or get sucked in like stock or inferior-quality aftermarket gaskets • Superior quality silicone/steel gaskets outlast cork and rubber composite designs to provide years of dependable service, especially when constantly removing and reinstalling valve covers • Full 3/16"-thick • Two per package |
| PART # | DESCRIPTION |
| 93020 $56.54 | Perm-Align Valve Cover Gasket Fits: SBC, Moroso Valve Covers and others of similar design |
| 93021 $78.10 | Perm-Align Valve Cover Gasket Fits: 18,16,15,13.5 & 12° Dart, Brodix, Edelbrock and All Pro cylinder heads |
| 93040 $90.34 | Perm-Align Valve Cover Gasket Fits: BBC, Moroso Valve Covers and others of similar design |
| 93045 $78.18 | Perm-Align Valve Cover Gasket Fits: Big Chief (does not fit Dart Big Chief II, 11° Cylinder heads |
| 93050 $61.92 | Perm-Align Valve Cover Gasket. Fits: SB Chrysler |
| 93055 $63.26 | Perm-Align Valve Cover Gasket. Fits: BB Chrysler |
| 93060 $71.39 | Perm-Align Valve Cover Gasket. Fits: Ford 221, 260, 289, 302 and 351W, Moroso Valve Covers and others of similar design |
| 93065 $66.04 | Perm-Align Valve Cover Gasket. Fits: BB Ford |
|
Fits: Both Moroso GM LS Series and O.E.M. Valve Covers • Manufactured out of heavy duty molded rubber • Quality design and manufacturing meets or exceeds O.E.M. quality • Two per package |
| PART # | DESCRIPTION |
| 93025 $26.87 | Valve Cover Gasket, GM LS Series |
|
Big Block Chevrolet Fits: BBC • Set fits one valve cover, includes four 3" tabs and three 4" tabs with 5/16" diameter holes |
| PART # | DESCRIPTION |
| 68516 $28.22 | Valve Cover Hold Down Tabs, Steel, Chrome Plated |
| 68525 $40.49 | Valve Cover Hold Down Tabs, Steel, Powder Coated-Red |
| 68526 $40.49 | Valve Cover Hold Down Tabs, Steel, Powder Coated-Blue |
|
• Specifically designed to spread the fastener load over
a larger area of the valve cover flange to eliminate flange distortion
and subsequent oil leakage • Available in chrome plated steel, black, red and blue powder coated steel |
| PART # | DESCRIPTION |
| 68501 $33.70 | Valve Cover Hold Down Tabs, Steel, Powder Coated-Black with Clear Lacquer |
| 68505 $25.58 | Valve Cover Hold Down Tabs, Steel, Powder Coated-Red |
| 68506 $25.58 | Valve Cover Hold Down Tabs, Steel, Powder Coated-Blue |
| 68510 $18.85 | Valve Cover Hold Down Tabs, Steel, Chrome Plated |
|
VALVE COVER ACORN NUTS Fits: SBC or any valve cover using 1/4"-20 hold downs • Add a decorative touch to engines in cases where long valve cover wing nuts are impractical • Set includes eight 1-3/8" high nuts and 1/4"-20 x 1-3/8" studs |
| PART # | DESCRIPTION |
| 68561 $37.61 | Valve Cover Acorn Nuts for SBC, Chrome |
| 68562 $16.13 | Valve Cover, Acorn Nuts for BBC |
| PART # | REPLACEMENT PARTS |
| 97030 $9.99 | Studs 1/4"-20 x 1-3/8" |
|
Fits: SBC or any valve cover using 1/4"-20 hold downs • These studs were developed primarily for the oval track racer using Moroso Small Block Chevy cast aluminum valve covers where a leaking valve cover caused by a fastener shaking loose from vibration could mean disaster • Set consists of eight 1/4"-20 x 1-3/4" slotted head studs and eight 1/4"-20 nylon insert lock nuts with washers |
| PART # | DESCRIPTION |
| 68820 $14.76 | Valve Cover Stud Kit |
| PART # | REPLACEMENT PART |
| 97020 $10.08 | 8 Studs 1/4"-20 x 1-3/4", Slotted Head |
|
• Available in chrome plated steel or powder coated aluminum
colors including red, blue, black and clear • Includes matching studs to eliminate gasket alignment problems and to speed up installation • Four per pack • Extra Long Valve Cover Wing Nuts will clear 4-1/2" tall valve cover |
| PART # | DESCRIPTION |
| 68603 $34.98 | Extra Long Valve Cover Wing Nuts, 1/4"-20 with 1-3/8" long studs. Aluminum, Powder Coated-Black |
| 68604 $40.39 | Extra Long Valve Cover Wing Nuts, 1/4"-20 with 1-3/8" long studs. Aluminum, Powder Coated-Blue |
| 68605 $37.68 | Extra Long Valve Cover Wing Nuts, 1/4"-20 with 1-3/8" long studs. Aluminum, Powder Coated-Red |
| 68610 $25.52 | Extra Long Valve Cover Wing Nuts, 1/4"-20 with 1-3/8" long studs. Steel, Chrome Plated |
| 68621 $51.23 | Extra Long Valve Cover Wing Nuts, 5/16"-18 with 1-3/8" long studs. Aluminum, Powder Coated-Black to fit Pontiac 301-455 and Ford 332-428 FE Series and others |
| 68630 $37.68 | Extra Long Valve Cover Wing Nuts, 5/16"-18 with 1-3/8" long studs. Steel, Chrome Plated to fit Pontiac 301-455 and Ford 332-428 FE Series and others |
| 68640 $33.64 | Long Valve Cover Wing Nuts, 1/4"-20 with 1-3/8" long studs. Steel, Chrome Plated for stock height valve covers |
| PART # | REPLACEMENT PARTS |
| 97020 $10.08 | Studs, 1/4"-20 x 1-3/4", 8 per package |
| 97030 $9.99 | Studs, 1/4"-20 x 1-3/8", 8 per package |
| NOTE: Wing nut studs 1-3/4" long are packaged with our tall Small Block Chevy die-cast aluminum valve covers to allow for the thicker gasket flange on these covers. |
| PART # | DESCRIPTION |
| 68512 $16.12 | Valve Cover Hold Down Tabs, Steel, Chrome Plated |
|
• Set fits one valve cover, includes three 3" tabs
for the shallow recessed bolt holes and one 4" tab for the
deep recessed bolt hole • Use 1/4" washer face bolts for the two end holes |
| PART # | DESCRIPTION |
| 68519 $20.10 |
Valve Cover Hold Down Tabs, Steel, Chrome Plated |
| • Set fits one valve cover, includes four 5" tabs with 3/8" diameter holes |
| PART # | DESCRIPTION |
| 68530 $29.63 |
Valve Cover Hold Down Tabs, Steel, Chrome Plated |
|
• Use when space is critical or if the valve cover nuts
must be snugged down tighter than wing-nut-finger-tight • Four per package with 1/4"-20 x 1-3/8" studs included • Install and remove with half inch socket wrench with extension or a speed handle |
| PART # | DESCRIPTION |
| 68550 $49.76 | Valve Cover Hex Head Nuts, 1/2" hex head, 3-7/8" long, Chrome Plated Steel |
| PART # | REPLACEMENT PART |
| 97030 $9.99 | Studs 1/4"-20 x 1-3/8" |
|
• Bullet nose tip makes it easy to start mounting nuts • Prevents Small Block Chevy, Big Block Chevy & Small Block Chrysler cast aluminum valve covers from vibrating loose in competition • Includes eight 1/4"-20 x 1-1/2" heat-treated studs, nylon-insert lock nuts and washers |
| PART # | DESCRIPTION |
| 68830 $32.25 | Bullet Nose Valve Cover Stud Kit |
| 68831 $60.56 | Bullet Nose Valve Cover Stud Kit, 12 pt. nut |
| PART # | REPLACEMENT PARTS |
| 97035 $32.27 | Nuts, 12pt. |
| 97040 $30.98 | Studs, 1/4-20 & 28 Bullet Nose |
|
ONE PIECE PUSH-IN VALVE COVER BREATHERS Fits: Moroso or any valve cover with 1.22" hole • Designed to drain oil trapped in the foam back into the valve cover rather than allow it to drain out the air vents • Two per package except No. 68741. |
| PART # | DESCRIPTION |
| 68717 $56.61 * | One Piece Push-In Valve Cover Breathers, Aluminum, Powder Coated-Blue, |
| 68718 $56.63 * | One Piece Push-In Valve Cover Breathers, Aluminum, Powder Coated-Red |
| 68719 $56.52 * | One Piece Push-In Valve Cover Breathers, Aluminum, Powder Coated-Black |
| 68740 $22.77 * | One Piece Push-In Valve Cover Breathers, Steel, Chrome Plated |
| 68741 $13.37 * | One Piece Push-In Valve Cover Breathers, Steel, Chrome Plated, for street cars that require a PCV set-up. Contains one breather with valve cover grommet and one PCV valve grommet |
| PART # | REPLACEMENT PART |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
Fits: All valve covers with 1.22" holes; includes rubber
grommet • No. 68781, is ideal for plumbing your crankcase ventilation system into the air cleaner, while No. 68780, is a direct breather replacement for No. 25900, Crankcase Evacuation System • Uses internal foam disc and baffling to prevent oil from entering air cleaner No. 68781. |
| PART # | DESCRIPTION |
| 68780 $16.08 * | Replacement Breather/Oil Separator, for No. 25900, Crankcase Evacuation System, 5/8" Hose, Gold Iridite |
| 68781 $17.35 * | Replacement Breather/Oil Separator, 3/4" Hose, Chrome (for street use only) |
| PART # | REPLACEMENT PARTS |
| 97340 $6.24 | Breather/Filler Cap Grommets |
|
• Meets rule requirement for cars running 7.99 E.T. and
quicker • Threaded tube with collar mounts from inside valve cover through 1.22" opening; breather screws into the tube for secure attachment • Viton gasket resists oil, alcohol and race fuel to form airtight seal • Jam nuts allow breather to be positioned to suit plumbing requirements • Internal stainless steel baffling keeps oil/air separated • Clear finish resists rust • Includes all mounting hardware; one per pack |
| PART # | DESCRIPTION |
| 68785 $90.34 * | Positive Locking Breather, with Tube for 3/4" hose |
|
• Reduces crankcase pressure throughout entire rpm range
for increased piston ring seal, reduced intake charge contamination,
and fewer oil leaks • Track and dyno tests prove increases in engine performance • Includes 2 each: Oil Separators/Breathers, Breather/Filler Cap Grommets, One-Way Check Valve and Weld-In Nipple for header collector, use with 5/8" dia. hose |
| PART # | DESCRIPTION |
| 25900 $99.78 * | Crankcase Evacuation System |
| PART # | ACCESSORIES |
| 68788 $149.66 | Breather |
| PART # | REPLACEMENT PARTS |
| 68780 $16.08 | Oil Separator/Breathers |
| 97800 $29.61 | Check Valve for Header Collector |
| 97810 $16.00 | Weld-in Nipple for Header Collector |
|
• Manufactured from 6061 Billet Aluminum • Screws to valve cover for positive fit, does not push on • Designed in two pieces with a top that unscrews to allow for oil filling and easier cleaning or replacement of oil separator filter • Slip-on fitting for pan evac system • O-ring Seal . no gaskets (reduces leakage) • Meets rule requirement for cars running 7.99 E.T. and quicker |
| PART # | DESCRIPTION |
| 68788 $149.66 * | Positive Locking Billet Aluminum Filtered Breather |
| PART # | AVAILABLE OPTIONS |
| 22706 $12.03 | 1/2" NPT to -10AN Fitting |
| 22708 $20.09 | 1/2" NPT to -12AN Fitting |
|
CLAMP ON BREATHER • Clamps onto a 1" outside diameter tube • Fits Moroso Billet Aluminum Vacuum Relief Valves nos. 22633, 22636, and 22637. • Provides maximum protection against dirt and airborne debris without restricting air flow • Clamp included • Cleanable and re-usable: oil before use |
| PART # | DESCRIPTION |
| 68791 $35.05 * | Clamp On Breather, 1" I.D. |
|
• Kit contains two aluminum 1-3/8" O.D. breather tubes
with internal baffling, two half-hooded filtered breathers, and
two stainless hose clamps • Designed to be welded to Moroso valve covers and can be adapted to other aluminum covers |
| PART # | DESCRIPTION |
| 68800 $78.18 * | Weld-In Filtered Breather Kit |
| PART # | REPLACEMENT PARTS |
| 68811 $25.53 * | Filtered Breathers, with protective half-hood |
| 68812 $25.53 * | Filtered Breathers for early no. 68800, with 1-1/2" tube, half hood |
|
• Kit allows engine builder to install filtered breathers
on Moroso steel or aluminum valve covers (or other covers with
1.22" holes) without welding • Consists of two filtered breathers with clamps, two chrome plated adapter tubes and two valve cover grommets • Filters must be oiled before use |
| PART # | DESCRIPTION |
| 68810 $71.35 * | Push-In Filtered Breather Kit |
| PART # | REPLACEMENT PARTS |
| 68816 $28.22 * | Filtered Breathers Non-Hooded |
| 68812 $25.53 * | Filtered Breathers Half-Hooded |
|
VALVE COVER FiLtTERED BREATHERS • Available in half-hooded or non-hooded • Provides maximum protection against dirt and airborne debris without restricting air flow • Also available with completely exposed filter element and chrome plated top • Available in two types; Push-In or Clamp-On (for existing stacks; includes clamp) • Cleanable and re-usable; oil before use • One per pack |
| PART # | DESCRIPTION |
| 68811 $25.53 * | Valve Cover Filtered Breather, half-hood, clamp-on type. For Moroso Covers with welded-in stacks, 1/3/8" I.D. |
| 68812 $25.53 * | Valve Cover Filtered Breather, half-hood, clamp-on type. For Moroso Covers with welded-in stacks, 1-1/2" I.D. |
| 68813 $25.53 * | Valve Cover Filtered Breather, half-hood, push-In type. For Moroso Covers with 1.22" punched holes |
| 68815 $22.86 * | Valve Cover Filtered Breather, non-hooded style, clamp-on type. For Moroso Covers with welded-in stacks, 1-3/8" I.D. |
| 68816 $28.22 * | Valve Cover Filtered Breather, non-hooded style, clamp-on type. For Moroso Covers with welded-in stacks, 1-1/2" I.D. |
| 68817 $22.83 * | Valve Cover Filtered Breather, non-hooded style, push-in type. For Moroso Covers with 1.22" punched holes |
| 68818 $22.79 * | Filtered Breather, non-hooded style, clamp-on type. For Moroso Breather Tanks, 2" O.D. |
|
For Moroso GM LS Valve Covers or any 1-1/4" -12 Female Threaded
Bung/Opening . Provides an easy way of adding a breather to Moroso LS valve cover with an oil fill bung . Remove knurled cap on valve cover and screw in the Part no. 68841 $66.04 Breather Kit . Features a billet aluminum baffled screw in adapter with a 1" breather . Cleanable and re-usable filter |
| PART # | DESCRIPTION |
| 68841 $66.04 * | Breather Kit for Moroso GM LS Valve Cover |
| PART # | REPLACEMENT PARTS |
| 68791 $35.05 | Clamp on breather, 1" I.D. |
|
FOR SPRINT CAR ENGINES • Attaches to the valley pan on a sprint car engine • Kit includes 1 ¾" dia. tubing with 8 .5" long legs and a black anodized finish • Includes a billet aluminum clamp with mounting holes • Cleanable and re-usable filter |
| PART # | DESCRIPTION |
| 68850 $279.32 * | Breather Kit for Sprint Car Engines |
| PART # | REPLACEMENT PART |
| 68850-004 | Breather |
|
• Sprint Car racers can now mount an aluminum tube-style
crossover breather kit to their aluminum valve covers and save
some money in the process • Kit comes with all mounting hardware and aluminum bungs which must be welded to the valve covers |
| PART # | DESCRIPTION |
| 68762 $141.68 * | Valve Cover Breather Tube Kit, SBC Sprint Cars |
| PART # | ACCESSORIES |
| 68811 $25.53 * | Filtered Breathers, Half Hood |
| 68815 $22.86 * | Filtered Breathers, Non-Hooded |
| NOTE: Can only be used with aluminum valve covers. Breathers are not included with the kit and must be purchased separately. |
|
PCV GROMMETS FOR AFTERMARKET VALVE COVERS •Designed to work with Fabricated Sheet Metal and Cast Aluminum Valve Covers, without logo, that have a 1.220" diameter hole • Ideal for street enthusiasts using aftermarket valve covers and a positive crankcase ventilation system • Works with all popular GM PCV valves • Made from oil-resistant rubber |
| PART # | DESCRIPTION |
| 68770 $6.52 | PCV Grommets, 2 per package |
| 68771 $6.24 | PCV Grommets, 2 per package (Designed for .090 - .100" material thickness) |
|
• Designed to work with Fabricated Sheet Metal and Cast
Aluminum Valve Covers, without logo, that have a 1.220"
diameter hole • Replacement Valve Cover Grommets for breathers and oil filler caps; two per pack |
| PART # | DESCRIPTION |
| 97340 $6.24 | Breather/Filler Cap Grommets |
| 97341 $6.24 | Breather/Filler Cap Grommets (Designed for .090-.100" material thickness) |
|
With Integral Baffle • Designed to work with Fabricated Sheet Metal and Cast Aluminum Valve Covers, without logo, that have a 1.220" diameter hole • Ideal for those using aftermarket valve covers without OEM-style oil control baffles • Ideally suited for push-in style breather systems • Will not clear stud girdles • Made from oil resistant rubber |
| PART # | DESCRIPTION |
| 68775 $7.17 | Breather Grommet/Baffle, 2 per package |
| 68776 $6.89 | Breather Grommet/Baffle, 2 per package (Designed for .090 - .100" material thickness) |
|
With Integral Baffle • Designed to work with Fabricated Sheet Metal and Cast Aluminum Valve Covers, without logo, that have a 1.220" diameter hole • Ideal for those using aftermarket valve covers without OEM-style oil control baffles • Works with all popular GM PCV valves • Special design keeps oil out of the PCV valve • Will not clear stud girdles, made from oil resistant rubber |
| PART # | DESCRIPTION |
| 68772 $5.24 | PCV Grommet/Baffle, 1 per package |
| 68773 $5.21 | PCV Grommet/Baffle, 1 per package (Designed for .090 - .100" material thickness) |
|
• Made of 14 gauge 6061-T6 aluminum, this baffle mounts
inside Moroso valve covers under the breather hole to keep oil
from getting into the breather • Use with Valve Cover Breathers nos. 68720, 68721, 68722, 68723, 68724, 68725, 68730, 68740, 68741, 68781, 68810, 68813, or 68817. • Cannot be used with engines equipped with stud girdles • One per package; includes all necessary fasteners |
| PART # | DESCRIPTION |
| 68790 $8.24 | Valve Cover Breather Baffle |
|
• Can be welded to aluminum valve covers, holding tanks,
cylinder heads, oil pans, etc. or wherever an NPT fitting is
needed • Made of 6061-T6 aluminum and fit a 1" diameter hole • Two per pack |
| PART # | DESCRIPTION |
| 68900 $18.78 | Aluminum Weld-In Bungs, 3/8" NPT Fitting |
| 68910 $18.78 | Aluminum Weld-In Bungs, 1/2" NPT Fitting |
|
FILLER CAP KITS, UNIVERSAL FILLER CAP KITS • Cap Kit no. 85280 $44.42 and no. 85282 $35.02 are knurled • Cap Kit no. 85283 $49.80 is designed with contoured grip • These universal kits, available with steel or 6061-T6 aluminum bung, can be used on valve covers and other locations to replenish fluid, or serve as an inspection port • Bungs can be welded to any suitable tank, valve cover or plate • Manufactured from 6061-T6 aluminum, includes O-Rings for leak-free sealing |
| PART # | DESCRIPTION |
| 85280 $44.42 | Filler Cap Kit, Universal, Steel Bung, 1-1/4" -12UNF Threads, 1.5" OD |
| 85282 $35.02 | Filler Cap Kit, Universal, Aluminum Bung, 1-1/4" -12UNF Threads, 1.5" OD |
| 85283 $49.80 | Filler Cap Kit, Universal, Aluminum Bung, Black Anodized with logo, 1-3/8" -12UNF Threads, 2.6" OD |
|
• Provides an easy way of adding an oil fill to a valve
cover, tank, rear end and other locations • Available in two versions, - Non-Weld, for aluminum or steel, since no welding is required then there is not the possibility of heat damage to chrome or powder coat - Weld On, for steel, Steel Bung • Finger Grip cap manufactured from 6061-T6 billet aluminum with a black anodized finish, Moroso logo, includes O-Ring for leak free sealing |
| PART # | DESCRIPTION |
| 68485 $67.45 | Fill Cap Kit, Non-Weld, 1-1/4"-12UNF Threads, 1.5" O.D. |
| 85284 $44.42 | Fill Cap Kit,Weld, Steel, 1-1/4"-12UNF Threads, 1.5" O.D. |
|
Non-Weld • Non-weld kit, makes it easy to add a leak proof fitting to oil pans for oil returns, valve covers etc., without having to actually weld the fitting • Perfect for adding a fitting to steel or aluminum with up to a 1/8" max. wall thickness • O-ring seal to prevent leaks |
| PART # | DESCRIPTION |
| 22753 $35.02 | -10AN Male Fitting, Non-Weld |
|
Fits: All Moroso and OEM valve covers with 1.22" diameter
hole • Push-in design for applications requiring a sealing-type filler plug • Chrome plated top section |
| PART # | DESCRIPTION |
| 68660 $9.25 | Oil Filler Cap |